The 74HC; 74HCT is an 8-bit buffer/line driver with 3-state outputs. The device can be used as two 4-bit buffers or one 8-bit buffer. Buffers: vs is an octal unidirectional buffer. The 8 lines can be split into two groups and each group can be individually. Electrical Engineering Glossary of Electronic Terms, 8-Bit Buffer IC, functional schematic diagram, true table and package out-line. 74HCT

Author: Goltibei Gukasa
Country: Eritrea
Language: English (Spanish)
Genre: Education
Published (Last): 1 April 2006
Pages: 409
PDF File Size: 15.50 Mb
ePub File Size: 5.1 Mb
ISBN: 546-9-34545-799-7
Downloads: 23566
Price: Free* [*Free Regsitration Required]
Uploader: Shaktikasa

In this case, the input data is sent to the output. The output value will be “Z”, the impedance is approaching infinity. When the data input is nothing and the control input is open, the output value will be “Z”, which means no current and high impedance. This kind of buffer produces the state opposite to the input.

From Wikipedia, the free encyclopedia. However what is available in the IC family may also come into play. Note that the chip displayed indicates OE control of the output [Output Enable]. Other than size, Lead Inductance is the next important issue because it slows down switching time, while the size of the IC package causes the placement of the capacitor to move away from the power leads of the IC.

Digital buffer – Wikipedia

It draws very little current and will not disturb the original circuit. The high input impedance is the reason a voltage buffer is used. Data input is active but control input is inactive. It reads an input and outputs a value. The output value will be high if and only if the input value is high. Pick a series [54x] if need the temperature range, otherwise use the series [74x]. Because the resistance is infinity, the circuit will draw very little current, and will not disturb the original circuit.


Because the output current is generated by the voltage source via buffer, the buffer acts as a barrier between the source and load, thus preventing the load resistance affecting the source network. Nuffer page was last edited on 19 Septemberat The output value is 0, which means no current.

Buffer | Techshopbd

A Tri-state buffer, with its control input, can prevent a bus from reading excessive input. The digital buffer is important because it can control the on and off of data transmission, which is used widely in the world of registers sophisticated data storage device and buses data transferring device.

The output value will be 1 and current will flow through the element. A voltage buffer has a very high input impedance the opposition to current flow viewed from the load.

Design Hint; Because this chip is used to drive a bus, which may be capacitive loaded, use more than the normal by-pass capacitor to insure that the IC has the current it needs when the buffers begin to drive the bus. It is basically the same as active high digital buffer except the fact that the buffer is active when the control input is at a low state.

Digital buffer

Decoders, state machines, and other sophisticated digital devices may use inverters. Regardless of the family used, just be sure to provide by-pass next to the IC. Both the data and the control input are inactive; the buffer shuts down. Both data input and control input is active. A digital buffer or a voltage buffer is an electronic circuit element that is used to isolate the input from the output, providing either no voltage or a voltage that is same as the input voltage.


As a result, the power source will not be affected. The buffrr is biffer basic building block in digital electronics. The location of the bypass capacitor is extremely important; read more on Capacitor Placementas it applies to IC by-passing. A digital buffer serves to transfer a voltage from a circuit that has a high output impedance level, to a second circuit with a low input impedance level.

Note that 54xx devices are listed to the left and only the 74xx devices are listed above. Finally, note that the manufacturer is bfufer listed here either.

Electronic Engineering Glossary Terms

Data input is nothing but control input is active. Although we allow the data transmission by turning on buvfer control input, we don’t have data coming in because of the infinite resistance.

Views Read Edit View history. A circuit with a voltage buffer will always draw a little amount of current because of the high input impedance of the buffr. The suffix is used to define the package style [which is listed] and the packaging method during shipping [which is a don’t care].

Tri-state voltage buffers are used widely on buseswhich allows multiple devices communicate with each other. When the control input is active, the output value is the input value, and the buffer is not different from the single input digital buffer.

This article was written by admin