ABB ACS150 USER MANUAL PDF

ABB ACS Operation Limits. Setup the For settings of other parameters/ macros and detailed explanation hereof, see the instructions manual from ABB. View and Download ABB ACS user manual online. ACS Controller pdf manual download. The ABB ACS series component drives are easy to select and come with a variety of standard features acsuser-manual-partpdf.

Author: Mekinos Yogal
Country: Republic of Macedonia
Language: English (Spanish)
Genre: Health and Food
Published (Last): 8 September 2014
Pages: 486
PDF File Size: 6.31 Mb
ePub File Size: 12.19 Mb
ISBN: 294-6-80056-486-4
Downloads: 68962
Price: Free* [*Free Regsitration Required]
Uploader: Fegar

How to do common tasks The table below lists common tasks, the mode in which mxnual can perform them and the page number where the steps to do the task are described in detail. It also instructs in using the panel in control, monitoring and changing the hser. Motor Potentiometer macro This macro provides a cost-effective interface for PLCs that vary the speed of the drive using only digital signals.

Available for two seconds at start, otherwise as long as 2max allowed by the drive temperature.

Industrial Component Drives ACS150

Motor Ground the qbb end of the PE conductor at the distribution board. Routing the cables Route the motor cable away from other cable routes.

Page The total heat dissipation is the sum of the heat dissipation in the main and control circuits. Page 16 Hardware description Electrical installation What this chapter contains The chapter describes the electrical installation procedure of the drive.

Got it, continue to print. Must be equal to the acs510 on the motor Type rating plate. Check that there are no faults or alarms shown in the display. Using the information given in this chapter most alarm and fault causes can be identified and corrected.

  AUDIOVISUAL TRANSLATION SUBTITLING DIAZ CINTAS PDF

Connections and switch The diagram shows the connections and switch of the ACS Motor cables of several drives can be run in parallel aca150 next to each other.

ABB ACS USER MANUAL Pdf Download.

Wait until task is completed. You find the type code on the type designation label attached to the drive. Page 20 Fasten clamping plates 1. Parameters which are hidden by the FlashDrop device mxnual not visible. Safety Safety What this chapter contains The chapter contains the safety instructions which you must follow when installing, operating and servicing the drive. The function is useful in applications where a smooth and quick restarting is essential.

When you have changed the parameter value, starts flashing. If ignored, physical injury or death may follow, or damage may occur to the drive, motor or driven equipment. Page Below is a simple wiring diagram example. Motor cable Drive min. Page 49 Output mode In the Output mode, mwnual can: Selects the application macro or activates FlashDrop parameter values. Set the motor data to exactly the same value scs150 on the motor nameplate. During the delay the drive knows accurately the rotor position.

Make sure that dust from drilling does not enter the acs1150 during the Compatibility The manual is compatible with the ACS drive firmware version 1. Dimensions Dimensional drawings of the ACS are shown below. Reference mode In the Reference mode, you can: It provides three constant speeds. How to reset The drive can be reset either by pressing the keypad key on the control panel, through digital input, or by switching the supply voltage off for a while.

  LES AJOUTS CIMENTAIRES PDF

ABB ACSACSACSACS Documentation

Stop the drive and disconnect it from the AC power source. Page 8 ABB Standard macro Fan failure can be predicted by the increasing noise from the fan bearings. If the drive is acw150 in a critical part of a process, fan replacement is recommended once these symptoms start appearing. See chapter Fault tracing for the codes.

F used for drive internal temperature measurement is open or short-circuited. By pressing ‘print’ button you will print only current page. Overcurrent msnual limit for drive is Check motor and motor cable including phasing.

Installation and commissioning flowchart Task Identify the frame size of your drive: Follow the instructions in chapter Safety on page 5. Free space around the uswr The required free space for cooling above and below the drive is 75 mm 3 in. Page 47 How to start, stop and switch between local and remote control You can start, stop and switch between local and remote control in any mode. Page 45 The ACS includes an integrated potentiometer located at the front of the drive.

This article was written by admin