Clean only with a dry cloth – and as directed by Bose Corporation. Unplug this product from the wall The Bose® link AL8 Homewide Wireless Audio Link. FREE 2-day Shipping: The Bose link AL8 homewide wireless audio link is the easiest way to expand your Bose Lifestyle® system to additional rooms. The Bose link AL8 wireless homewide audio link is the easiest way to expand your Lifestyle® system to additional rooms.

Author: Tokinos Fauramar
Country: Estonia
Language: English (Spanish)
Genre: Travel
Published (Last): 20 June 2009
Pages: 312
PDF File Size: 8.13 Mb
ePub File Size: 15.41 Mb
ISBN: 518-1-31826-596-7
Downloads: 79535
Price: Free* [*Free Regsitration Required]
Uploader: Tygocage

So they are talking it would seem I have tried putting them right next to each other – same result. When they lose connection, do you get a solid or blinking orange LED? My manual says that they default to avoid channel 11, but this is beside the point, as I tested while my WLAN was turned off completely.

I’ve found it to be easier to actually just log into your router and set the channel to 6 so you don’t need to manually adjust the avoidance channel for the AL Curiously, have you tried the steps that have been outlined in the thread already? What troubleshooting steps have you taken so far? Cleared the wifi in the house on channel 1 and set up the AL8 so it doesn’t use channel 1. Below ao8 the list in order on what channels will be avoided based on each 3-second button push.

Thank you bos your reply.

BOSE(R) AL8 Homewide Wireless Audio Link

I also noticed that I get the same result if I la8 no Bose Link cables attached. However, no signals from my remote ever seemed to arrive at the AL-8, even in the 20 seconds before the connection broke down. There are two things that are most likely to get us closer to the issue:.

I have done all that I know how to do and am a dead end I have the same problem.


Bose link AL8 wireless home-wide audio link – No Color

Out of the box, the AL-8 and AR-1 will default to avoid channel 6 on a 2. Per Bose wifi or cable modem does not effect the AL8. If you look at the back of the AL-8 there is a button labeled “channel”.

Do you currently have these connected to a media center or not? I’ve unplugged the router and still get the same bkse.

I will continue to troubleshoot.

I’m sorry to hear that. You may need to send boose signal through to get them to recognize each other. I plug them all in at the same time and they all stay green for 20 seconds. The AL8 and AR1s were engineered to operate on 2. When they lose connection, they go to solid orange. If the LED does not blink in response to each button press, the issue is the remote. Unfortunately i can not move the wifi or the AL8. Is it certain that there actually is a connection in the first 20 seconds, just because the lights turn green?

Cable is connected to the input jack on the tx and Bose Link “out” on the back of the Lifestyle V Thank you for giving a detailed explanation of your setup and troubleshooting steps taken. Thanks for the tip. The transmitter tx and receiver ql8 for the AL8 aren’t communicating.

BOSE(R) AL8 Homewide Wireless Audio Link – video dailymotion

A push and hold of the button will get you to “No wifi network” the first time which is only used if you don’t have Wi-Fithen to avoid channel 6, then avoid channel 11, 1, 2, and so on. The LED should turn off whenever a button on the remote is pressed. Let’s unplug your blse altogether at a time when noone in the household is using the internet and see if they connect. Then after 20 seconds at the same time, the transmitter turns solid orange while the 2 receivers start la8 blink green.


Now I need find out how I can kill or isolate the 2.

But as soon as the tx goes orange, the rx starts to blink green and search. Both are on the same “setup” code and I’ve tried different “setup” codes, but no luck.

Believe the problem is with the Bose Link AL8, but listed the other equipment in the title for completeness.

Should they connect to each other even without Bose Link to a Lifestyle console or an expansion set? But then, for unknown reasons If not, the problem may be the Bose Link instead of the wireless connection. I’ve also tried the Bose Bosr “in” as well, but the same result. Yes, the dip switches match. Can you check the dip switches on the back of your AL-8 and AR-1 to make sure they match the same pattern?

Both near to be in the same area due to drops. I’ve been troubleshooting it boes months with Bose and no solid solution. This used to work, but now it doesn’t. I just noticed your post.

Do you have any suggestions on isolating that broadcast? With the system on steady green LED – start up completepress any button on the expansion remote while looking at the front of the control console. In that al88 second window while the lights are still green, let’s test the expansion remote and ensure that the control console is responding to it. These days most routers are set to channel hop or auto-detect so you’d need to log into your router and set the channel setting itself to 6 so it stays there.

This article was written by admin