A major revision to ASTM F has been completed and the new specification will appear in the ” ASTM Book of Specifications Volume Plastic. ASTM F (D) Conduit · Innerduct Warranty · Innerduct Material Specification · F (D & D) Complete Part Number Chart · Enduct True. F (D) Data Sheet · ASTM F Conduit All Types · Innerduct Material Specification · Part Number Chart · Innerduct Warranty · ASTM F (D).
|Published (Last):||20 November 2009|
|PDF File Size:||8.39 Mb|
|ePub File Size:||2.72 Mb|
|Price:||Free* [*Free Regsitration Required]|
It is informational only and not an official part of the standard; the full text of the standard itself atsm be referred to for its use and application. This specification covers material, dimensional, workmanship and performance requirements for polyethylene conduit, duct and innerduct manufactured for use in a nonpressure application with communication, CATV, or power wire and cables.
The product shall be subject to elongation, impact, and ovality tests. D Speciman I. Workmanship The duct shall be free of visible cracks, holes or other physical defects that would degrade its performance. Request the technical instruction guide for C.
Print 1 2 3 4 5 f1260 sstarting from page current page. No further reproductions authorized. Markings The duct shall have a durable identification showing the name or trademark of the manufacturer, duct size i.
Historical Version s – view previous versions of standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. ASTM does not give any warranty express or implied ast make any representation that the contents of this abstract are accurate, complete or up to date.
The rope can be provided with varying strengths as needed for a particular installation. The duct shall also be capable of being encased in qstm.
High Density Polyethylene Duct
The internal or external surface may contain a coextruded layer provided the finished conduit meets the specified product requirements. Installation The duct shall be capable of being direct buried by plowing or trenching with no special consideration to using selective backfill.
Content only available by subscription. This will keep coupling requirements to a minimum. Other special markings can be agreed upon between the buyer and seller. Flow Rates of Thermoplastics by Extrusion Plastometer.
Enduct F O.D Controlled Conduit
It shall be ast, to bend the duct to a minimum supported radius of 10 diameters. The duct shall be capable of being coiled reeled in continuous lengths, transported, stored outdoors and subsequently uncoiled for installation – without affecting its properties or performance. Description The duct shall be manufactured from virgin high density polyethylene. Check with a manufacturer for specifications.
Because the fire retardant process eliminates UV protection, Fire-Retardant duct must be installed safe from exposure to UV light.
Enduct Schedule 40 & 80
This specification covers material, dimensional, workmanship and performance requirements for polyethylene conduit, duct and innerduct manufactured for use in a nonpressure application with communication, CATV, or power wire and cables.
Referenced Documents purchase separately The documents listed below are referenced within the subject standard but are not provided as part of the standard. Tensile Properties of Plastics. There were no books found for the applied search filters.
The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.
This standard does not purport to address all of astn safety concerns, if any, associated with its use.
Application High Density Polyethelene Duct has been tested and proven under the most severe conditions. Special Options Striped Duct – Three longitudinal stripes can be extruded on any standard size of smooth duct of f216 color.
The product shall be subject to elongation, impact, and ovality tests. The electronic file may not be reproduced in any way. Enter your personal account email address to request a password reset: ASTM grants you a license as follows: There is no additional charge for Ast Duct. Are you sure you want to empty the cart? Sequentially-Marked Duct – Duct can be ordered with numbering – every asfm feet ashm printed on the duct.
Design Considerations Please refer to our technical data brochure.
F21660 to Active This link will always route to the current Active version of the standard. Environmental Stress-Cracking of Ethylene Plastics. Please refer to our technical data brochure. This abstract is a brief summary of the referenced standard. In addition the electronic files may not be downloaded or distributed elsewhere over computer networks or otherwise.
It shall be as uniform as practicable in respect to overall dimensions, color, density, thickness, etc. Polyethylene Plastics Molding and Extrusion Materials. The internal or external surface may contain a coextruded layer provided the finished conduit meets the specified product requirements.
Striped Duct – Three longitudinal stripes can be extruded on any standard size of smooth duct of any color.
Ovality out-of-roundness and curvature are inherent characteristics of coiled, continuous length HDPE conduit. Search book title Enter keywords for book title search.
The data listed was astk on press molded test specimens, and may therefore deviate from specimens taken from pipes. The duct specified for aerial installation shall be ultraviolet light-resistant.