ATTANSIC ATTP1 PDF

, 13, ATTANSIC, -. Kring Electronics Co., Ltd. , -, Attansic, sop8. 63, 0, ATTANSIC, -. Rantle East Electronic. , -, ATTANSIC, SOP. 年12月11日 ATTP1_ – Technology Corporation ATTP1 Over Temperature Please contact Attansic Technology Corp. for the latest documents. Attansic. ATTP1. Tel:. MFG:. ATTANSIC. Picture. D/C:. 09+. QTY:. Packaging:. SOP8L. Package:. Note:. 原装正品. Support. No“ATTP1”Picture.

Author: Bragor Fauzilkree
Country: Madagascar
Language: English (Spanish)
Genre: Business
Published (Last): 18 July 2016
Pages: 28
PDF File Size: 7.30 Mb
ePub File Size: 4.31 Mb
ISBN: 172-9-36898-458-2
Downloads: 63824
Price: Free* [*Free Regsitration Required]
Uploader: Malall

Where’s the thermal diode? You will find that it is easiest to attanslc the jumper agtp1 the diagonal under the CPU socket between the pins. I didn’t think it did.

Soldering on these quad flat packs is a real PITA! In my case, I actually took a chance with my CPU to try it out.

That is one of the reasons I did it the way I did, so that you could undo it if necessary. I’ve got pretty steady hands and it took me three tries to get the jumper soldered correctly without bridging solder to the other pins. Our members offer you their FAQs! While this mod works pretty well, it has one glaring drawback, which I mentioned in the previous post: You should thread the jumper first, then solder attannsic the Attansic chip, then finally solder to the Winbond chip.

Run a jumper from pin 61 of the Winbond chip to pin It’s already in the right place.

ATTP1 Attansic CPU thermal protection controller chip SOP8

How to test OTP? That’s all there is to it. As a result, when you tie the Attznsic 3 input to the thermal diode while the Attansic chip is hooked up, it causes the Attansic chip to think that the CPU has exceeded safe temp limits.

  HANUL ANCUTEI PDF

As for the northbridge, does it have a thermal diode?

This is the analog voltage input. If you have previously modded your mobo to attanaic the thermal diode, you MAY find that your temps are degrees higher than they used to be.

I believe the AN7 has a thermal probe under the north bridge. I’ve personally verified this a few times myself, so I know it works. The possibilities are endless! Lift artp1 pin just as you did pin Anything else is nearly impossible. I sttp1 to type in short sentence. Make sure you leave just a dollop of solder on the end of the jumper wire when you tin it or you’ll never get it to solder properly but don’t leave too much, or you’ll bridge the pins.

Tie the analog voltage supply for the Winbond chip to the 5vsb rail instead of the 5v rail.

A fine tip soldering iron is definitely a must. This means that your poor CPU is going to blow its brains out just as soon as it loses proper cooling for any reason. You’ll find that trying to solder the wires to the broken pins, while not impossible, is exceedingly difficult. Check out our sister site! It is more likely that you will mess it up such that the OTP function trips prematurely and you aren’t able to power on the computer at all.

  DIODO GUNN PDF

Find pin 97 of the Winbond chip. This is the top right pin on the Attansic chip, when viewed with the mobo oriented as described above.

You don’t need to move the jumper though. The jumper wire will need to be about 3. Webb City, Mo Posts: So what is the solution? Also make sure that you don’t accidentally bridge any of the adjacent pins with solder while you are trying to lift this pin. It is the pin at the very top left corner of the Winbond chip on the top, when viewed as described above. This is the 5vsb input.

ATTP1(ATTANSIC,SOP-8), DataSheet|Picture – Electronic Parts – Censtry Electronics Co.,Ltd.

I’ve been looking for developer’s docs for the NF2 chipset and haven’t atp1 able to find any. The wire will need to be about 8 cm 3″ long. However, be aware that soldering pin 97 and pin back down is rather tricky because of the fine spacing of the pins.

Well, I’ve solved that problem.

Apply a dollop of gel type super glue or some other fastening agent to each of your jumpers to near pin 97 and pin to keep them from flexing too much and breaking the pins off the chip.

This article was written by admin