AUDIOVOX CCS-100 MANUAL PDF

Follow the instructions in the CCS Manual. Using the VSS signal on a standard (manual) transmission vehicles Murphs CCS and the original Audiovox. only, and is not intended to replace the CCS Installation Manual. Manual, for those persons that choose to install the CCS cruise. Auto and car manuals and free pdf automotive manual instructions. Find the user manual Audiovox CCS Automobile Accessories User Manual. Page 1.

Author: Tern Misho
Country: Trinidad & Tobago
Language: English (Spanish)
Genre: Love
Published (Last): 4 November 2012
Pages: 193
PDF File Size: 20.15 Mb
ePub File Size: 4.73 Mb
ISBN: 548-2-51288-441-6
Downloads: 13369
Price: Free* [*Free Regsitration Required]
Uploader: Dugis

This confirms that you have a good tach signal. If you are installing the cruise to a motorcycle, determine where you are mounting the cruise control keypad. Pull on the wires…If they come loose you found your problem.

Seal off the end off the vacuum line to the engine with you finger. Cc-100 can always shut the cruise off by turning the cruise off at the control keypad. Too much slack and the cruise will be slow to respond.

For automobiles, use the connection methods as described in the original CCS manual at http: Start the bike and leave it in neutral: Routing the Main Wiring Harness 1. Wear all your gear just in case.

Murphs CCS controls engine speeds using a tachometer signal and engine vacuum to control vehicle speed. Should the throttle ever stick, pull in the clutch first then hit the kill switch. You can reduce the Sensitivity Settings which will make the cruise less jerky at low speeds at the expense of not holding speed as well at higher speed. The control circuit interprets digital speed information from the car’s engine control module VSS or Magnet Kit and ignition coil output.

  AGUSTIN BARRIOS LA CATEDRAL III ALLEGRO SOLEMNE PDF

The port marked AUX is connected to the vacuum port on the cruise servo.

When you press on either brake the Red LED inside the servo should be continuously lit. Build a mount for the cruise control keypad if needed. Locate the fused wire with switch connector included in the kit, and load the Brown, Green, and Yellow wires from the main harness into the 4 audiocox switch connector.

Page of 19 Go. Pursuit series keyless entry alarm upgrade module 8 pages.

Audiovox Automobile Accessories CCS User Guide |

Tachometer only speed signal SW4, SW5: Brake Wire Connection Test: Speed Sensor Installation Step 6: Comments to this Manuals Your Name.

Snap the second wire into the remaining slots making sure the ends are cvs-100 opposite the first wire, as shown in Figure 4 or If you already have a SPDT relay in the brake circuit, either you have the uadiovox relay or you have it connected wrong. Don’t show me this message again. Coil Tachometer source 4 Throttle connection: Another good source for information on cruise control installation is the numerous online vehicle specific forums. Rearview mirror with 4″ color lcd monitor and camera package v2.

  ENCICLICA DIES DOMINI PDF

Page 19 Audiovox Corp. Do some advance planning cvs-100 determine where you are mounting the cruise servo and the vacuum reservoir. The faster the sensitivity, the less the speed drops. See if your vehicle has an online forum.

Audiovox CCS-100 Installation Manual

Find the problem and fix it before you ride your bike. That might not be safe if a fuse blows.

Follow the instructions in the CCS Manual. If the Red LED inside the servo shuts off, either the brake lights are stuck on and you need to readjust the brake switch or you need to use a SPDT relay in the brake circuit.

Throttle Wire Loop example: Disengagement and no-engagement decisions are based on the monitored information.

Page 3 The Cruise Module makes “decisions” audioovox upon speed,tachometer, and brake signal information. The Purple Servo wire must be connected to chassis ground for the Cruise to turn on.

This article was written by admin