DG201ABK DATASHEET PDF

DGABK datasheet, DGABK pdf, DGABK data sheet, datasheet, data sheet, pdf, Intersil, Quad SPST, CMOS Analog Switches. DGABK Datasheet, DGABK PDF, DGABK Data sheet, DGABK manual, DGABK pdf, DGABK, datenblatt, Electronics DGABK. DGABK datasheet, DGABK circuit, DGABK data sheet: MAXIM – Quad SPST CMOS Analog Switches,alldatasheet, datasheet, Datasheet search site.

Author: Totilar Didal
Country: Malta
Language: English (Spanish)
Genre: Science
Published (Last): 4 March 2016
Pages: 31
PDF File Size: 19.20 Mb
ePub File Size: 14.57 Mb
ISBN: 418-5-21943-261-3
Downloads: 89536
Price: Free* [*Free Regsitration Required]
Uploader: Zunos

Dimensions b1 and c1 apply to lead base metal only. A notch or a pin one identification mark shall be located adjacent to pin one and shall be located within the shaded area shown. N is the maximum number of terminal positions. Dimension Q shall be measured from the seating plane to the base plane.

Selected parts for the query dg

Daasheet dimension allows for off-center lid, meniscus, and glass overrun. For the latest package outline information, go to www. Mold flash or protrusions shall not exceed 0. Maxim guarantees that these switches will not latch up if the power supplies are disconnected with input signals still connected. In case of conflict between English and Metric dimensions, the inch dimensions control. Package Information continued The package drawing s in this data sheet may not reflect the most current specifications.

Copyright Intersil Americas Dataaheet. For more information on TYP values see Note 2. Information furnished by Intersil is believed to be accurate and reliable. These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures.

Parameter guaranteed by design or characterization. For this configuration dimension b3 replaces dimension b2. VO is the steady state output with switch on. Maxim reserves the right to change the circuitry and specifications without notice at any time.

  ASTM D2500 PDF

In the OFF state each channel blocks voltages up to the supply rails.

No license is granted by implication or otherwise under any patent or patent rights of Intersil or its subsidiaries. For more information on TYP values see Note 3.

Limit diode current to maximum current ratings. Measure dimension S1 at all four corners. When the enable input is high, a channel is selected by the address inputs, and when low, all channels are off. Putere n-am, Tu-mi fii sprijin. However, no responsibility is assumed by Intersil or its subsidiaries for its use; nor for any infringements of patents or other rights of third parties which may result from its use.

Device mounted with all leads soldered to PC board. No circuit patent licenses are implied. B1 maximum dimensions do not include dambar protrusions.

Lab 6 in this note. Documents Flashcards Grammar checker.

DGA Intersil Quad SPST, CMOS Analog Switches ChipFind Datasheet Archive |

The DG has a maximum turn-off time of ns and a maximum turn-on time of ns. These are stress ratings only, and functional operation d201abk the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied.

An enable input is provided. D, D1, and E1 dimensions do not include mold flash or protrusions. The addition of these diodes will reduce the analog signal range to 1V below the positive supply and 1V above the negative supply.

Feedthrough via gate capacitance may result in spikes at leading and trailing edge of output waveform. Dambar protrusions shall not exceed 0.

Datasheet «DG201A»

Maxim cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim datasheeet. Asa cum sunt, la Tine vin! SR Datasheet – Micropower Direct. The DGA has a maximum turn-off time of ns and a maximum turn-on time of ns. For information regarding Intersil Corporation and its dg201ab, see www. Exposure to absolute maximum rating conditions for extended periods may affect device reliability.

  COMO NACEN LOS OBJETOS BRUNO MUNARI PDF

In either case, source-to-body diodes can be forward biased and conduct current from the signal source. Accordingly, the reader is cautioned to verify that data sheets gd201abk current before placing orders. The algebraic convention whereby the most negative value is a minimum, and the most positive value is a maximum, is used in this data sheet. Dimension M applies to lead plating and finish thickness. Pin Configurations continued To provide protection for overvoltages up to 20V above the supplies, a 1N or 1N type diode should be placed in series with the positive and negative supplies as shown in Figure 2.

DGABK Datasheet, PDF – Alldatasheet

Typical values are for design aid only, not guaranteed and not subject to production testing. The maximum limits of lead dimensions b and c or M shall be measured at the centroid of the finished lead surfaces, when solder dip or tin plate lead finish is applied. This is a stress only rating and operation of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied.

E and eA are measured with the leads constrained to be perpendicular to datum -C. All Rights Reserved All other trademarks mentioned are the property of their respective owners.

This article was written by admin