FBI XL2T PROGRAM PDF

Introduction The XL-2T is a state of the art microprocessor-based control/ communicator. The system features seven (7) fully programmable zones. Programming. XL-2T. Security System. Installation and Setup Guide. STAY. INSTANT. ACYLB. READY APPENDIX D – SYSTEM PROGRAMMING WORKSHEET. Example: To program phone number enter 1#8#0#0# etc. Exit Program STAY. Default Panel Short “EEPROM RESET” pins on panel and power up system.

Author: Makree Mezigar
Country: South Sudan
Language: English (Spanish)
Genre: Politics
Published (Last): 10 June 2018
Pages: 145
PDF File Size: 5.55 Mb
ePub File Size: 8.49 Mb
ISBN: 755-1-48977-242-8
Downloads: 53366
Price: Free* [*Free Regsitration Required]
Uploader: Nejin

Section 5 – System Operations 4. For UL installations see wiring diagram for hookup. The system must be in ready mode.

To print the manual completely, please, download it. The rear plastic mounting plate is not used for recessed installations. Directly to a single or double gang electrical junction box.

On LED keypads the sounder will beep after each entry. Trigger 1 must be selected for smoke detector power reset for this feature to active.

FBI XL-2 Program Sheet

I then pressed code button followed by master codethen user no 3 and then new 4 digit user code. Secure keypad to double-gang box as shown in graphic at left. The double-gang box shall be mounted flush with wall in order for keypad screws to fit. The keypad will indicate a trouble on the fire zone if the bell or sounder is not properly connected.

  A REFERENCE GRAMMAR OF MODERN STANDARD ARABIC KARIN C.RYDING PDF

For Built-in Siren Driver, connect a single 8 ohm speaker only. The auto arm time represents the time of xk2t that the area will automatically arm if it is not already armed.

When the switch is pushed toward the front of the keypad, in the opposite direction of the arrowthe switch is in the OFF position. The checkmark highlights which options are selected. To select a trigger type enter the 2 digits in either L1 L2 or L3 L4 desired trigger type for each output trigger. I pressed the code button ready light did not flashthen pressed both 7 and 9 at same time, to reset master code to Page 23 Fire Trouble is reported to the CS if enabled program question 32, location 3.

This xk2t Fire and Burg zones to report restores. Don’t have an account? The FCC requires the following statement for your information. The purpose of this manual is to give you a brief overview of the XL-2T control panel, and provide instructions for installing a basic system.

At the moment telephone line seizure occurs, the Telco Tip is momentary connected to earth ground to access dial tone. A-2 Partial Extended 3×1 Part. See the following diagram: If selected, then a negative acknowledgment 4 short beeps will be xl2r after attempting to enter this mode.

FBII XL-2T Installation And Setup Manual

Enter text from picture: Directly to a control panel having a keypad cutout on the front of its enclosure. By pressing ‘print’ button you will print only current page.

  DDA 2010 HOUSING SCHEME BROCHURE PDF

The Extended Reporting Format: Question 11, L1 – Exit Delay Separate the two halves of the keypad by placing a straight-slot screwdriver into one of the two slots at the bottom of the keypad and twisting.

The door of the metal cabinet may be removed to make it easier to install the control panel. Section 6 – System Programming When programming the English zone descriptors, use the following techniques to program the characters: The keypads can be surface mounted or flush mounted as described below. The following is a quick comparison.

The alarm was then activated, without me activating it. Create an opening and mount a standard double-gang box. Page 70 Section 6 – System Programming When programming the English zone descriptors, use the following techniques to program the characters: The system contains up to fifteen user codes 4 digits each with the following applications: Next, enter the desired account number each digit followed by the key.

Got it, continue to print. Question 32, L1 – Bypass Code

This article was written by admin