FLYGT 3152 PDF

2. C C Product. Submersible pump for pumping clean water, surface water and waste water containing solids or long-fibred material. Denomination. Dataplate. rpm. Max 40°C. YSER/Y//V. 26/51A. kWhp. Date: Flygt CS MT. Use our handy online form to submit details on your existing Flygt pump to get a Flygt C Submersible Pumps Range Flygt C LT Submersible.

Author: Vimuro Mezilrajas
Country: Georgia
Language: English (Spanish)
Genre: Art
Published (Last): 16 April 2013
Pages: 195
PDF File Size: 5.78 Mb
ePub File Size: 13.15 Mb
ISBN: 253-3-93886-548-5
Downloads: 25784
Price: Free* [*Free Regsitration Required]
Uploader: Visida

Product specifications | Flygt 3152 – Alaska Pump and Supply

Check the control circuit and functions. Measures to secure performance and pump efficiency are defined and decided for each individual application. Due to its design it is best suited for pumps in a vertical position. Replace the worn parts. The unit and the components can be heavy. EN approval plate EN approval for cable entry: If the pump is flytg version, assemble the pump. Remove the entrance cover and the O-ring from the stator housing.

Check the oil level in the oil housing. This is an example of a serial number, and an explanation of its parts.

Flygt 3000 Series / C Submersible Pumps

Make sure that the pump cannot rotate at startup or during operation. Before assembling the pump housing or diffuser ring with the drive unit end, check the following: Lifting device Check that local safety regulations are followed. Unscrew the four cap nuts and withdraw the lower wear protection from the pump housing. This rule applies to both ends of the cable. Dispose of all packing materials in accordance with local regulations. Remove the impeller, impeller hub, or propeller using a impeller hub.

  CSS2 PRATIQUE DU DESIGN WEB PDF

Drive in the new wear ring. Run a cable between the sump and the stator and monitoring equipment. Handle the sensor with care.

Keep the end of the motor cable above the liquid level. Flygt Installation, Operation, and Maintenance Tlygt 47 Troubleshooting Troubleshooting Introduction Follow these guidelines when troubleshooting the pump: If the insulation is less: Oversized lifting equipment could cause damage if the unit should stick when being lifted.

The pipes are obstructed. Clean chemicals from the eyes 1. Failure to do so may result in hearing loss or violation of local laws.

Replace the valves, if necessary. Install with S-installation In the S-installation, the pump is transportable and intended to operate either completely or partially submerged in the pumped liquid. Hold your eyelids apart forcibly with your fingers. Always disconnect and lock out power before servicing to prevent unexpected startup.

The clearance is adjusted with the sleeve screws. Leakage into the electrical parts can cause damaged equipment or a blown fuse. Temperature class Maximum ambient temperature Figure 3: If there is a question regarding the intended use of the equipment, please contact an Xylem representative before proceeding. File a claim with the shipping company if anything is out of order.

  ALGORITHMIC ARCHITECTURE KOSTAS TERZIDIS PDF

The impeller wear ring 1.

Flygt – Alaska Pump and Supply |

Place the pump in a horizontal position. Check the contactor and the control circuit.

Thermistor must never be exposed to voltages higher than 2. Check that the monitoring fygt works. F Required tools for F These are the personnel requirements for Ex-approved products in potentially explosive atmospheres: Up to 24, hours or 6 years, whichever comes first. If the pump has a hole with the markings “oil out” it is important that this hole is used for drainage.

Install flyggt entrance cover and the O-ring on the stator housing. Electrical connections regulations Electrical connections must be made by certified electricians in compliance with all international, national, state, and local regulations. The wear ring in the pump housing 1. Make sure the unit hangs straight up and down 31152 the lifting hook. Use this safety equipment within the work area: The data plate lists key product specifications.

This article was written by admin