HR15DE WIRING PDF

– wiring (Denso) for Wingroad with Y12, Electrics. Frame / Series, Y12 / Y12, body, W (wagon), engine, HR15DE (HR15DE engine), drive, 2WD. HR15DE engine model. flexible wires and anchors, work properly. If loose parts, deterioration, cuts .. to any components or wiring of the supple- mental air . HR15DE engine torque curve. Achieves plentiful low-end torque extending through mid-to-high engine speed. MR20DE engine torque curve. liter engine.

Author: Dokasa Moramar
Country: Swaziland
Language: English (Spanish)
Genre: Photos
Published (Last): 7 November 2017
Pages: 313
PDF File Size: 10.71 Mb
ePub File Size: 5.90 Mb
ISBN: 266-3-86909-388-8
Downloads: 35062
Price: Free* [*Free Regsitration Required]
Uploader: Shakajin

After warming up – Keeping the engine speed between 3, and 4, rpm for 1 minute and at idle for 1 minute under no load? So, the acceleration will be poor.

File:Nissan HR15DE engine 001.JPG

ON Heater fan switch: Fully depressed Accelerator pedal: Response ratio Lean to Rich Response rate: This page was last edited on 9 Marchat More than 1 second after turning ignition switch ON [Engine is running] [Ignition switch: After warning up, idle the engine? After warming up, idle the engine?

Specification data are reference values. P P P P Detected items Mass air flow sensor circuit Engine coolant temperature sensor circuit Engine operating condition in fail safe mode Engine speed hg15de not rise more than 2, rpm due to the fuel cut. By using this site, you agree to the Terms of Use and Privacy Policy.

  FACTORING FORFAITING PDF

ENGINE / nissan | part list|

Slightly depressed Air conditioner switch: Fully depressed — [Engine is running]? Not being turned Steering wheel: For 1 seconds after turning ignition switch: You may do so in any reasonable manner, but not in any way that suggests the licensor endorses you or your use.

Slightly depressed [Ignition switch: Battery voltage 11 — 14 V 0. H15de file contains additional information such as Exif metadata which may hrr15de been added by the digital camera, scanner, or software program used to create or digitize it. Therefore, acceleration will be poor.

Revving engine from idle up to 3, rpm quickly after the following conditions are met. Views View Edit History.

Fully released Brake pedal: Vehicle has traveled after MI has turned ON. Engine is warmed up to normal operating temperature and running under no load. About 2, rpm More than seconds after starting wkring. Below 3, rpm after the following conditions are met.

Wiring for – Nissan TIIDA/TIIDA LATIO C11 | Japan sales region, ,

Before measuring the terminal voltage, confirm that the battery is fully charged. Below 3, rpm after the following conditions are met – Engine: Fully depressed — — 0. ON] [Engine is running]?

  LIBRO ESCUCHAR MUSICA AARON COPLAND PDF

Idle air volume learning has not been performed yet. Power generation voltage variable control: For 1 second after turning ignition switch ON [Engine is running] [Ignition switch: ECM is located in the engine room left side near battery.

Nissan HR engine

Idle speed [Engine is running]? Average voltage for pulse signal Actual pulse wirinv can be confirmed by oscilloscope. ON] O — — — [Ignition switch: After warming up – After keeping engine speed between 3, and 4, rpm for 1 minute and at idle for 1 minute under no load?

ECM controls the electric throttle wirinh by regulating the throttle opening around the idle position. ON] — [Ignition switch: Fully depressed — 5V 0. When ECM calculation function is malfunctioning: ON] — — [Ignition switch: A few seconds after turning ignition switch OFF [Ignition switch:

This article was written by admin