IBANEZ S520EX MANUAL PDF

The SEX is an S series solid body electric guitar model introduced by Ibanez in It was initially produced in Korea and then later in Indonesia. There’s no way a guy who does a couple guitar setups every day of the year would do a better than someone will with instructions from the. For over 18 years, Ibanez RG guitars with Edge double locking sys- tems have been SEX MOF. • 3pc Wizard II Manually Adjustable Zero. Point System.

Author: Donos Goltigar
Country: Fiji
Language: English (Spanish)
Genre: Environment
Published (Last): 15 August 2014
Pages: 180
PDF File Size: 10.90 Mb
ePub File Size: 14.59 Mb
ISBN: 604-3-42400-809-1
Downloads: 5186
Price: Free* [*Free Regsitration Required]
Uploader: Tet

Wind the string around the tuning machine and tune to pitch. The Saddles are preset on the plate. The height adjustment of the tremolo can be set by using the two 3mm adjustment screws on either side of the tremolo unit. Adjusting the string Height.

The rotation torque of the arm can be adjusted by changing the number of bushings on the arm. Solid Body Electric Guitars.

When the guitar is properly adjusted, tighten the top lock pressure pad screws 5. After changing the desired strings retune all the strings to the proper pitch and tighter the top lock pressure pad screws. To change the strings angle adjust the two 2mm 6 screws on the highside of the bridge, chanding the pivot angle.

Open the new bushings at the split section and snap them into place on the tremolo arm.

S520EX (2005–2009)

Intonation adjustment is usually necessary when new strings are fitted it can also be affected by the angle of the tremolo unit.

Insert the tremolo arm into the arm socket and firmly push down until the arm snaps into place Note: Use an electronic tuner and tune the guitar to a standard pitch. To allow the arm to swing freely.

  AS5040 DATASHEET PDF

Play the harmonic at the 12th fret, compare it to the fretted noteat the 12th fret, these notes should read the same on the tuner. For ease in retuning, it is recommended that one string at a time be changed and tuned.

Tighten the pressure pad screws. Loosen the heigth adjustment screw 5 on both sides of the bridge using a 2 Phillips.

Cut off the ball end of the new string above the string winding and insert the end of the string in between the main s520ed and the string holder block. To further reduce the torque, remove both bushings.

SEX (–) | Ibanez Wiki | FANDOM powered by Wikia

All lbanez guitars use A for a standard pitch. Raise or lower the tremolo to the desired string height using a 3mm allen wrench. The purpose of this manial to accommodate for different tunings or different gauges of strings. Adjusting the String Height. The Overall Tremolo height can be adjusted by raising or lowering the Height Adjustment screws 5 on either side of the bridge.

If the 12th fret is flatter than the open note, the saddle needs to be moved forward. Turn the notched wheel 4 To raise or lower the bridge.

This is caused by the string vibrating. Adjusting the intonation is performed by moving the individual string saddles forward or backward. Raise or lower the tremolo to the desired string height using a 4mm allen wrench. If the 12th fret is sharper than the open note, the saddle needs to be moved back. The height adjustment of the tremolo can be set by using the two 4mm adjustment screws 2 on either side of the tremolo unit.

  HSBC ZERTIFIKATE UND OPTIONSSCHEINE PDF

To reduce the torque, remove one bushing on the lower side.

| Wiring Diagrams

Height adjustment of the individual strings can be adjusted by useing a 1. Loosen the string stopper screw 8 by using a 3mm allen wrench remove the string from the saddle. Occasionally, there are times when the neck may need adjustment. Tremolo Angle Adjustment The tremolo system should sit parallel to the surface of the guitar body, as shown in the illustration.

Retune the guitar to the proper pitch and check the angle.

Using a Phillips head screw driver, turn the Spring tension adjustment screw and adjust the length of the spring. Loosen the pressure pad lock screws on the top lock with a 3mm ianez wrench. Thread the new string through the string holder tubeand over the saddle pulling it tight towards the headstock.

Make sure the truss rod is properly 5s20ex before adjusting the action. If the intonation is still not correct repeat steps 1, 2 and 3. Wlnd the string around the tuning machine and tune to pitch.

When the guitar is properly adjusted, tighten the top lock pressure pad screws. Both bushings should be completely hidden. Only loosen the manuaal enough to move the saddle.

Wiring Diagrams

Loosen the Saddle lack down screw 9 on the saddle to be adjusted with a 2mm allen wrench. Loosen iganez string stopper bolt by using a 3mm allen wrench, and remove the string from the saddle. Adjust the saddle forward or backward to the proper position and tighten the Saddlelock down screw 9.

This article was written by admin