ICM7208 DATASHEET PDF

Intersil Corp ICM datasheet, 7-Digit LED Display Counter (1-page), ICM datasheet, ICM pdf, ICM datasheet pdf, ICM pinouts. Part, ICM Category. Description, 7-digit LED Display Counter. Company, Intersil Corporation. Datasheet, Download ICM datasheet. Quote. ICM 7-Digit LED Display Counter Components datasheet pdf data sheet FREE from Datasheet (data sheet) search for integrated circuits.

Author: Kigajas Sakus
Country: Indonesia
Language: English (Spanish)
Genre: Automotive
Published (Last): 7 September 2013
Pages: 25
PDF File Size: 3.98 Mb
ePub File Size: 3.37 Mb
ISBN: 488-4-73454-415-1
Downloads: 57793
Price: Free* [*Free Regsitration Required]
Uploader: Mezirg

CA equivalent IC Abstract: The ICM is intended to operaterange for high frequency applications. The ICM is intended to operate over a supply voltage of 2 to 6 volts as a medium speed counter, orrecommended that the ICM be used in conjunction with the ICM Oscillator Controller, which provides a. It is an older counter and I found it in my grandpa’s basement. If I were really looking for an adapter to fit something, that would be one place I’d stop.

Ten input pulses must be counted in order for a 1 to appear on the first digit, Dl, so that the frequency being measured is obviously 10 times larger than the frequency that is shown on the display. That red and black wire going to the switch should give you some clue for finding ground. Is there any way to hard wire this to a power supply? Previous 1 2 Next. The ICM is intended to operate over a supply voltage ofapplications.

ICM7208 – 7-Digit LED Display Counter

Skip – RedRock https: Specifically the ICM provides the following on chip functions: ICMDcounting window. But I have a quick question: Horizontal Transistor TT Abstract: The ICM is intended torange for high frequency applications. As a frequency counter it is recommended that the ICM be used in conjunction with the. As a frequency counter it fs recommended that the ICM be. The frequency of the pulses is determined by the state of U2 pin That signal is input to Ul at pin 16 and is used to scan the display digits in sequence.

  DURUFLE QUATRE MOTETS PDF

Again, thanks for getting back to me so quick on that! When pin 11 of U2 is taken to ground through SI, the pulses occur every 2 seconds and cause U2 pin to go high for one second, which prevents additional input signals from entering Ul. C chips part numbers sanded off which makes repair difficult.

The crystal frequency is further divided to produce a short store pulse at pin 2 of U2, followed after about 0.

As a frequency counter it is recommended that the ICM be. Figure 3 shows the recommended input gating waveforms to the ICM Integrated circuit Ul counts input signals, decodes them to 7-segment format, and outputs signals that are used to drive a 7-digit display. The display must have at least seven 7-segment common-cathode multiplexed LED digits. Simple Metal detector circuit with CD Home All times are UTC. I couldn’t find a ground on the circuit board. I do greatly appreciate it.

If you can find a circuit trace on the board that is the same as that spring thingy, it will work for power ground. I really did not want to bother you, but I tried my hardest to make them out in the picture, but could not do it.

Any common-cathode seven-segment display can be used; no particular display is specified. Simple deep searching metal detector circuit. Timebase G e n e ra to r. Echo Depth Sounding Sonar for Boats.

Integrated circuit U2 provides the timing for Ul, wliile U3 conditions the input signal to provide a suitable waveform for input to Ul. From our catalog scanning project.

  CARA MEMBUAT HERBARIUM PDF

Thanks I’ll give that a try and see if it works! Other frequency counters using the.

T&L Publications

Hope you get yours wired up ok! Fully automatic watering circuit for flower pots. Although your counter is not identical to mine, it does appear to use a similar circuit. Go ahead and post here.

> meter counter > Frequency meter > 10Mhz Frequency Counter Circuit l –

Specifically daatasheet ICM provides the following on chip functionsgenerate the multiplex frequency reference, and the control switches. That cycle is repeated, continuously updating the display every two seconds. If you still have the cover off of your frequency counter can you tell me the part numbers on all the I.

No file text available. The cathodes of each digit are taken to ground several times each second, activating any segments of the digits whose anodes are high as the result icm720 decoding by Ul. In that mode, the decimal points are driven by and visually indicate that the 0.

Figure 6 shows the recommended input gating waveforms to the ICM You do not have the required permissions to view the files attached to this post. Integrated circuit U2 pin 13 then goes low for one second, allowing a new count to be ick7208 into the seven decade counters of Ul. This forum is for all my fellow radio dataheet, or up and coming radio operators to seek or give advice.

I have located the positive wire

This article was written by admin