INTEL 8255 DATASHEET PDF

DATASHEET. The Intersil 82C55A is a high performance CMOS version of the industry standard A and is manufactured using a. The Intel (or i) Programmable Peripheral Interface (PPI) chip was developed and .. , Complete Description about the Intel IC; , Datasheet; , functions overview; The Intel (or i) Programmable Peripheral Interface (PPI) chip .. “PCI A Datasheet” (). 6.

Author: Kidal Midal
Country: Guadeloupe
Language: English (Spanish)
Genre: Education
Published (Last): 17 November 2005
Pages: 345
PDF File Size: 17.97 Mb
ePub File Size: 14.88 Mb
ISBN: 509-7-36238-320-6
Downloads: 94268
Price: Free* [*Free Regsitration Required]
Uploader: Tegor

Intel 8255

The two halves of port C can be either used together as an additional 8-bit port, or lntel can be used as individual 4-bit ports. Acknowledgement and handshaking signals are provided to maintain proper data flow and synchronisation between the data transmitter and receiver.

From Wikipedia, the free encyclopedia. Only port A can be initialized in this mode. If an input changes inttel the port is being read then the result may be indeterminate.

Retrieved from ” https: This means that data can be input or output on the same eight lines PA0 – PA7. This mode is selected when D 7 bit of the Control Word Register is 1. In this mode, the may be used to extend the system bus to a slave microprocessor or to transfer data bytes to and from a floppy disk controller.

It is an active-low signal, i.

This means that data can be input or output on the same eight lines PA0 – PA7. Only port A can be initialized in this mode. The is a member of the MCS Family of chips, designed by Intel for use with their and microprocessors and their descendants [1]. Intel Intel D Input and Output data are latched.

  BURN FOR BURN BY JENNY HAN AND SIOBHAN VIVIAN PDF

By using this site, you agree to the Terms of Use and Privacy Policy. Retrieved 3 June The two modes are selected on the basis of the value present at datqsheet D 7 bit of the control word register. Retrieved 3 June The control signal chip select CS pin 6 is used to enable the chip. For port B in this mode irrespective inteo whether is acting as an input port or output portPC0, Dagasheet and PC2 pins function as handshake lines.

Programmable Peripheral Interface – Intel Chipset Datasheet

Interrupt logic is supported. Port A can be used for bidirectional itnel data transfer. Microprocessor And Its Applications. Acknowledgement and handshaking signals are provided to maintain proper data flow and synchronisation between the data transmitter and receiver.

It is an active-low signal, i. Since the two halves of port C are independent, they may be used such that one-half is initialized as an input port while the other half is initialized dahasheet an output port.

The two modes are selected on the basis of the value present at the D 7 dataxheet of the control word register. All of these chips were originally available in a pin DIL package.

The is also directly compatible with the Zas well as many Intel processors. Port A can be used for bidirectional handshake data transfer.

A Datasheet pdf – PROGRAMMABLE PERIPHERAL INTERFACE – Intel

Microprocessor And Its Applications. The Intel or i programmable peripheral interface PPI chip was developed and manufactured intell Intel in the first half of the s for the Intel microprocessor and is a member of dayasheet MCS Family of chips.

As an example, consider an input device connected to at port A. Some of the pins of port C function as handshake lines. In this mode, the may be used to extend the system bus to a slave microprocessor or to transfer data bytes to and from a floppy disk controller.

  LEY 12510 SANTA FE PDF

For port B in this mode irrespective of whether is acting as an input port or output portPC0, PC1 and PC2 pins function as handshake lines. Since the two halves of port C are independent, they may be used such that one-half is initialized as an input port while the other half is initialized as an output port. If from the previous operation, port A is initialized as an output port and if is not reset before using the current configuration, then there is a possibility of damage of either the input device connected or or both, since both and the device connected will be sending out data.

Interrupt logic is supported.

This mode is selected when D 7 bit of the Dataxheet Word Register is 1. For example, if port B and upper port C have to be datashset as input ports and lower port C and port A as output ports all in mode When we wish to use port A or port B for handshake strobed input or output operation, we initialise that port in mode 1 port A and port B can be initilalised to operate in different modes, i.

This article was written by admin