LF357 DATASHEET PDF

LF JFET Input Operational Amplifiers. These are the first monolithic JFET input operational amplifiers to incorporate well matched, high voltage JFETs on the. LF datasheet, LF circuit, LF data sheet: STMICROELECTRONICS – WIDE BANDWIDTH SINGLE J-FET OPERATIONAL AMPLIFIERS,alldatasheet. LF datasheet, LF circuit, LF data sheet: TI – LF/LF/LF/ LF/LF/LF/LF JFET Input Operational Amplifiers,alldatasheet.

Author: Mohn Mikar
Country: Burundi
Language: English (Spanish)
Genre: History
Published (Last): 26 January 2015
Pages: 190
PDF File Size: 5.25 Mb
ePub File Size: 15.45 Mb
ISBN: 773-4-78190-173-9
Downloads: 68940
Price: Free* [*Free Regsitration Required]
Uploader: Faell

All other trademarks are the property of their respective owners. This information is the most current data available for the designated devices. Output Impedance Figure Important Information and Datasyeet Open-Loop Voltage Gain Figure First, the user must not ignore the surface leakage of the PCB, even though it may sometimes appear acceptably low, because under conditions of high humidity or dust or contamination, the surface leakage will be appreciable.

LF Datasheet PDF ( Pinout ) – Series Monolithic JFET Input Operational Amplifiers

To compensate add C2 such that: Negative Current Limit Figure 8. We recommend that these same precautions be adhered to, during all phases of inspection, test and assembly. Documents Flashcards Grammar checker. PDIP package Soldering 10 sec. These are stress ratings only, which do not imply functional operation of the device at these or any other conditions beyond those indicated under Recommended Operating Conditions.

Device is in production to support existing customers, but Dataseet does not recommend using this part in a new design. Gain Bandwidth Figure Categories include technical documents, support and community resources, tools and software, and quick access to sample or buy.

The drain currents for the amplifiers are therefore essentially independent of supply voltage. Device has been announced but is not in production. If a line is indented then it is a continuation of the previous line and the two combined represent the entire Device Marking for that device.

LF357 Datasheet

However, neither of the input voltages should be allowed to exceed the negative supply as this will cause large currents to flow which can result in a destroyed unit. TI has taken and continues to take reasonable steps to provide representative and accurate information but may not have datasheft destructive testing or chemical analysis on incoming materials and chemicals.

  HONEYWELL R7241 PDF

Fortunately, the techniques of obtaining low leakages are quite simple. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI.

Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. When the LFx5x is manufactured, the device is always handled with conductive finger cots. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes. This data is subject to change without notice and revision of this document. Common-Mode Rejection Ratio Figure Equivalent Input Noise Voltage Figure Typical Connections Of Datawheet Rings The designer should be aware that when it is inappropriate to lay out dataheet PCB for the sake of just a lr357 circuits, there is another technique which is even better than a guard ring on a PCB: Linked contents are provided “AS IS” by the respective contributors.

Exceeding the negative common-mode limit on either input will force the output to a high state, potentially causing a reversal of phase to the output. Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. If a guard ring is used dstasheet held close to the potential of the datasheey inputs, it will significantly reduce this leakage current.

TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release. Except where mandated by applicable law, testing of all parameters of each component is not necessarily performed.

TI bases dxtasheet knowledge and belief on information provided by third parties, and makes no representation or warranty as to the accuracy of such information. Finish options are separated by a vertical ruled line. Overall system slower than fast sample and hold R1, CC: These amplifiers feature low input bias and offset currents, as well as low offset voltage and offset voltage drift, coupled with offset adjust which does not degrade drift or common-mode rejection.

  KAZIMIERZ SZEWCZYK BIOETYKA PDF

Efforts are underway to better integrate information from third parties. This component has a RoHS lr357 for either 1 lead-based flip-chip solder bumps used between the die and package, or 2 lead-based die adhesive used between the die and leadframe.

In this case you may have to forego some of the advantages of PCB construction, but the advantages are sometimes well worth the effort of using point-to-point up-in-the-air wiring. To minimize the effect of any surface leakage, lay out a ring of foil completely surrounding the inputs of the LFx5x and the terminals of capacitors, diodes, conductors, resistors, relay terminals, and so forth, connected to the inputs of the op amp, as in Figure Unless otherwise specified the absolute maximum negative input voltage is equal to the negative power supply voltage.

Settling Time Test Circuit 8. TI has discontinued the production of the device. Use of a heat sink is recommended if input bias current is to be kept to a minimum.

Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements l357 its products, and any use of TI components in its applications, notwithstanding any applications-related information or support that may be provided by TI. However, if the feedback pole is less than approximately six times the expected 3-dB frequency a lead capacitor should be placed from the output to the input of the op amp.

Input Bias Current Figure 3. Common-mode rejection and open-loop voltage gain are also unaffected by offset adjustment. Exceeding the negative common-mode limit on both inputs will force the amplifier output to a high state. When one wishes to take advantage of the low input bias current of the LFx5x, typically less than 30 pA, it is essential darasheet have an excellent layout.

For browser-based versions of this data sheet, refer to the left-hand navigation.

This article was written by admin